Cuatro pilares están fijos en la parte inferior y conectados por un bloque rígido en la parte superior. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Una viga de madera reforzada con dos placas de acero en los extremos está cargada por presión. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Una viga de madera reforzada con dos placas de acero en los extremos está cargada por presión. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Este ejemplo de verificación se basa en el ejemplo de verificación 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Un sistema de una sola masa con juego y dos muelles se deforma inicialmente. Determine the natural oscillations of the system - deflection, velocity, and acceleration time course.
Un bloque tridimensional hecho de material elástico-plástico con endurecimiento está fijado en ambos extremos. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.
Determinar la flecha máxima de un bloque tridimensional fijo en ambos extremos. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. The block's middle plane is subjected to vertical pressure.
Un bloque tridimensional hecho de material elástico-plástico está fijado en ambos extremos. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai-Wu plasticity theory.
Determine la flecha máxima de cuatro pilares fijos en la parte inferior y conectados por un bloque rígido en la parte superior. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
Un sistema monomasa con amortiguador está sometido a una fuerza de carga constante. Determine the deflection and velocity of the dashpot endpoint in the given test time.
A sphere is subjected to a uniform flow of viscous fluid. The velocity of the fluid is considered at infinity. The goal is to determine the drag force. The parameters of the problem are set so that the Reynolds number is small and the radius of the sphere is also small, thus the theoretical solution can be reached - Stokes flow (G. G. Stokes 1851).
El ejemplo de verificación describe las cargas de viento en varias direcciones del viento en un modelo de un grupo de edificios. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
Una estructura de pórtico de un solo vano de dos plantas está sometida a una carga sísmica. The modulus of elasticity and cross‑section of the frame beams are much larger than those of the columns, so the beams can be considered rigid. The elastic response spectrum is given by the standard SIA 261/1:2003. Neglecting self-weight and assuming the lumped masses are at the floor levels, determine the natural frequencies of the structure. For each frequency obtained, specify the standardized displacements of the floors as well as equivalent forces generated using the elastic response spectrum according to the standard SIA 261/1.2003.
El ejemplo de verificación describe el flujo estacionario alrededor de un edificio de gran altura entre bloques de apartamentos (modelo a escala). The example is given by the Architectural Institute of Japan (AIJ). The chosen results (velocity magnitude) are compared with the measured values.
El ejemplo de verificación describe el flujo en estado estacionario alrededor de un edificio aislado (modelo a escala).El Architectural Institute of Japan (AIJ) proporciona el ejemplo. The chosen results (velocity magnitude) are compared with the measured values.
Este ejemplo de verificación compara los cálculos de la carga de viento en un edificio con cubierta a dos aguas utilizando la norma ASCE 7-16 y utilizando la simulación CFD en RWIND Simulation. The building is defined according to the sketch and the inflow velocity profile taken from the ASCE 7-16 standard.
Este ejemplo de verificación compara los cálculos de la carga de viento en un edificio de cubierta plana utilizando la norma ASCE 7-16 y utilizando la simulación CFD en RWIND Simulation. The building is defined according to the sketch and the inflow velocity profile taken from the ASCE 7-16 standard.
El ejemplo de verificación compara el cálculo de la carga de viento en un edificio con una cubierta plana utilizando la norma EN 1991-1-4 y utilizando la simulación CFD en RWIND Simulation. The building is defined according to the sketch, and the inflow velocity profile is taken according to the standard EN 1991-1-4.
El ejemplo de verificación compara el cálculo de la carga de viento en un edificio con una cubierta a dos aguas utilizando la norma EN 1991-1-4 y utilizando la simulación CFD en RWIND Simulation. The building is defined according to the sketch, and the inflow velocity profile is taken according to the standard EN 1991-1-4.